Emulator
Mouse over to zoom in
- Product 3/3
-
Description
Mini ST-LINK/V2 on a small single board, an extreme low cost solution for in-circuit debugger/programmer for STM8 and STM32.
Features
1 Onboard 500mA self-recovery fuse to avoid harming by short circuit
2 Dual voltage output (3.3V/5V), easy for debugging/programming
3 Standard USB interface for direct connection to PC
4 Debugging/Programing performance
Debugging : run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc.
Programming : supports FLASH ROM, EEPROM, AFR, etc.
USB2.0 combined with SWIM/SWD interfaces : quick response for debugging & fast speed for programming
5 Upgradable firmware
The firmware is upgradable to support more devices in the future
Automatically upgraded
6 Supported software
ST-LINK Utility v2.0 (or higher ver.)
STVD Version 4.2.1 (or higher ver.)
STVP Version 3.2.3 (or higher ver.)
IAR EWARM Revision v6.20 (or higher ver.)
IAR EWSTM8 Revision v1.30 (or higher ver.)
KEIL RVMDK Revision v4.21 (or higher ver.)
ATOLLIC
TASKING
7 Supported devices
All the STM8 devices with SWIM interface
All the STM32 devices with SWD interface
ST-LINK/V2 (mini) Vs ST-LINK/V2 Vs ST-LINK
|
Compare |
ST-LINK/V2 (mini) |
ST-LINK/V2 |
ST-LINK |
Remarks |
|
SWD voltage range |
1.65V - 3.6V |
1.65V - 3.6V |
3V - 3.6V |
ST-LINK/V2 and ST-LINK/V2 (mini) support STM32 low voltage devices |
|
SWIM voltage range |
1.65V - 5.5V |
1.65V - 5.5V |
1.65V - 5.5V |
|
|
Supports SWV |
YES |
YES |
NO |
For the moment, only STM32 supports SWV while STM8 doesn't |
|
Debug interfaces |
2 |
2 |
1 |
ST-LINK/V2 and ST-LINK/V2 (mini) support STM8/STM32 with separated interfaces |
|
LED indicator |
Dual color LED |
Dual color LED |
Red LED |
Dual color LED allows indicating more status |
|
Fuse |
YES |
NO |
NO |
Fuse for avoid harming by short circuit |
Connecting with PC
While connecting the ST-LINK/V2 (mini) to the computer through USB interface, the USB driver is required and should be installed correctly first.
Connection with STM8/STM32 applications
The ST-LINK/V2 (mini) should be connected to the STM8 application via the SWIM interface.
|
Debugger Pin |
Target Board Pin |
Description |
|
VCC |
MCU VCC |
STM8 VCC |
|
SWIM |
MCU SWIM |
STM8 SWIM PIN |
|
GND |
GND |
STM8 GND |
|
RST |
MCU RESET |
STM8 RESET PIN |
The ST-LINK/V2 (mini) should be connected to the STM32 application via the SWD interface.
|
Debugger Pin |
Target Board Pin |
Description |
|
VCC |
MCU VCC |
STM32 VCC |
|
SWDIO |
MCU SWDIO |
STM32 SWD SWDIO |
|
GND |
GND |
STM32 GND |
|
SWCLK |
MCU SWCLK |
STM32 SWD SWCLK |
Please note that the VCC and GND should be connected correctly to avoid any harm to the ST-LINK/V2 (mini).
Package Contains
ST-LINK/V2 (mini) × 1
4-pin custom connector cable × 1
-
- $3.50
-
- $13.90
-
- $6.40
-
- $10.80
-
- $18.80
-
- $15.99
